root@bpi-r3:~# ethtool eth1
Settings for eth1:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  1000baseX/Full
        Link partner advertised pause frame use: Symmetric
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Auto-negotiation: on
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Current message level: 0x000000ff (255)
                               drv probe link timer ifdown ifup rx_err tx_err
        Link detected: yes
root@bpi-r3:~# ethtool -m eth1
        Identifier                                : 0x03 (SFP)
        Extended identifier                       : 0x04 (GBIC/SFP defined by 2-wire interface ID)
        Connector                                 : 0x07 (LC)
        Transceiver codes                         : 0x00 0x00 0x00 0x01 0x00 0x00 0x00 0x00 0x00
        Transceiver type                          : Ethernet: 1000BASE-SX
        Encoding                                  : 0x01 (8B/10B)
        BR, Nominal                               : 1300MBd
        Rate identifier                           : 0x00 (unspecified)
        Length (SMF,km)                           : 0km
        Length (SMF)                              : 0m
        Length (50um)                             : 550m
        Length (62.5um)                           : 270m
        Length (Copper)                           : 0m
        Length (OM3)                              : 0m
        Laser wavelength                          : 850nm
        Vendor name                               : OEM
        Vendor OUI                                : 00:90:65
        Vendor PN                                 : GLC-SX-MMD     _
        Vendor rev                                : _e
        Option values                             : 0x00 0x1a
        Option                                    : RX_LOS implemented
        Option                                    : TX_FAULT implemented
        Option                                    : TX_DISABLE implemented
        BR margin, max                            : 0%
        BR margin, min                            : 0%
        Vendor SN                                 : CSCGE1M14134
        Date code                                 : 220120
        Optical diagnostics support               : Yes
        Laser bias current                        : 3.482 mA
        Laser output power                        : 0.3181 mW / -4.97 dBm
        Receiver signal average optical power     : 0.3472 mW / -4.59 dBm
        Module temperature                        : 25.77 degrees C / 78.39 degrees F
        Module voltage                            : 3.3180 V
        Alarm/warning flags implemented           : Yes
        Laser bias current high alarm             : Off
        Laser bias current low alarm              : Off
        Laser bias current high warning           : Off
        Laser bias current low warning            : Off
        Laser output power high alarm             : Off
        Laser output power low alarm              : Off
        Laser output power high warning           : Off
        Laser output power low warning            : Off
        Module temperature high alarm             : Off
        Module temperature low alarm              : Off
        Module temperature high warning           : Off
        Module temperature low warning            : Off
        Module voltage high alarm                 : Off
        Module voltage low alarm                  : Off
        Module voltage high warning               : Off
        Module voltage low warning                : Off
        Laser rx power high alarm                 : Off
        Laser rx power low alarm                  : Off
        Laser rx power high warning               : Off
        Laser rx power low warning                : Off
        Laser bias current high alarm threshold   : 100.000 mA
        Laser bias current low alarm threshold    : 0.000 mA
        Laser bias current high warning threshold : 90.000 mA
        Laser bias current low warning threshold  : 0.100 mA
        Laser output power high alarm threshold   : 1.2589 mW / 1.00 dBm
        Laser output power low alarm threshold    : 0.0501 mW / -13.00 dBm
        Laser output power high warning threshold : 0.7943 mW / -1.00 dBm
        Laser output power low warning threshold  : 0.0631 mW / -12.00 dBm
        Module temperature high alarm threshold   : 90.00 degrees C / 194.00 degrees F
        Module temperature low alarm threshold    : -45.00 degrees C / -49.00 degrees F
        Module temperature high warning threshold : 85.00 degrees C / 185.00 degrees F
        Module temperature low warning threshold  : -40.00 degrees C / -40.00 degrees F
        Module voltage high alarm threshold       : 3.8000 V
        Module voltage low alarm threshold        : 2.7000 V
        Module voltage high warning threshold     : 3.7000 V
        Module voltage low warning threshold      : 2.8000 V
        Laser rx power high alarm threshold       : 0.7943 mW / -1.00 dBm
        Laser rx power low alarm threshold        : 0.0079 mW / -21.02 dBm
        Laser rx power high warning threshold     : 0.5012 mW / -3.00 dBm
        Laser rx power low warning threshold      : 0.0126 mW / -19.00 dBm
root@bpi-r3:~#