FW-WEB Wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== BananaPi R3 ======

https://wiki.banana-pi.org/Banana_Pi_BPI-R3
===== Hardware =====

  * MT7986(Filogic 830) quad core ARM A53 SoC
  * MT7531A Ethernet-switch
  * 2G DDR RAM
  * 8G eMMC flash, SPI-NAND (128 MiB), SPI-NOR (32 MiB)
  * dual-band wifi:
    * 2.4G use MT7975N
    * 5G (wifi 6/5.8GHz,not 6E) use MT7975P frontend
  * 2 SFP 2.5GbE and 5 GbE RJ45 ports
  * mPCIe slot with only USB 2.0 connected for 4G modem
  * M.2 slot key-M with only PCIe x2 interface (no sata/usb) for nvme (key B+M) or wifi-card for 6E (maybe adapter needed)

V1.0:

{{:en:bpi-r3:bpi-r3_top.jpg?direct&300 |}}{{ :en:bpi-r3:bpi-r3_bottom.jpg?direct&300 |}}


V1.1:

{{:en:bpi-r3:bpi-r3_11_top.jpg?direct&300 |}}{{ :en:bpi-r3:bpi-r3_11_bottom.jpg?direct&300 |}}
==== debug-uart ====

3v3 TTL

Usb2serial adapters supported: ch340 (no G),cp2104,FT4232

With Profilic, cp2102, ch340G wifi firmware does not start [[https://github.com/openwrt/mt76/issues/702|issue-report]]

Gnd-gnd,rx-tx,tx-rx

115200 8n1 (8databits,1 startbit), no flow control
==== bootmedium ====

  * SD / eMMC sharing 1 mmc-controller in SoC
    * SD 4bit bus, eMMC 8bit
    * switched first 4 data-lanes by sw6/D (bottom on v1.0)
  * SPI NAND/NOR sharing SPI0-Bus
    * CS switched by sw5/C

sw2/B on top of board near debug-uart chooses between SPI and MMC

see [[uboot#bootmedium_selection]] for boot selection table
==== Network connections ====


<code>
gmac1 (eth0) ---- (p6)mt7531(P0) ---- WAN
                            (P1-4) -- LANx4
                            (p5/lan4) ---- right SFP slot (sfp2)
gmac2 (eth1) ---- left SFP slot (sfp1)
</code>

https://forum.banana-pi.org/t/bpi-r3-information/12897/4

=== SFP ===

We have both sfp slots recognized and working

  mount -t debugfs none /sys/kernel/debug/
  ethtool -m eth1
  cat /sys/kernel/debug/sfp*/state

Some sfp are still not recognized (e.g. gpon).maybe quirks are needed.

After some phylink-conversion there are some issues with 2g5 sfp on left sfp/eth1. A workaround is disabling autoneg on the interface

  ethtool -s eth1 autoneg off

Left sfp does not support vlan in linux 6.1 because tag is stripped.

Power: "All SFP power supplies are connected to the system VDD33" which is 3v3/8A [[https://forum.banana-pi.org/t/banana-pi-bpi-r3-router-board-with-mediatek-mt7986-filogic-830-support-wi-fi-6-6e-2-5gbe-sfp/12933/31|source]] [[https://forum.banana-pi.org/t/bpi-r3-support-for-sfp-vdsl-modem/15320/5|Dts patch from Daniel]] I sent 3W patch to ML...

== compatibility ==

  * class: Fibre MM/SM, Copper RJ45, ONT
  * bandwidth: 1G/2G5 (only)

^ class ^ vendor / short ^ part no ^ supported bandwidth ^ state ^ Link ^ comment ^
| Fibre MM | H!Fibre for cisco | ASF85-24-X2-D | 1000baseX only | working | [[https://www.amazon.de/gp/product/B073VM49BK?th=1|Amazon]] [[https://www.hifiber.com/item/ASF85-24-X2-D/1000base-sx-sfp-850nm-550m-mmf-transceiver-module-customized.html|vendor]] | {{ :en:bpi-r3:hifibre_glc-sx-mmd.txt |}} |

2g5 sfp currently detected only if autoneg is turned off.

  ethtool -s eth1 autoneg off
  ethtool -s lan4 autoneg off

Eric works on phy driver which looks very good now for 6.6 (6.5-next),but now yet posted upstream.

=== WIFI ===

Firmware: https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/tree/mediatek

[[WLAN]]

Antenna mounting https://forum.banana-pi.org/t/how-to-mount-the-antenna-to-the-box/14429/4

Antenna order by band (5g in corners): https://forum.banana-pi.org/t/how-to-mount-the-antenna-to-the-box/14429/15

WED (wireless dispatch - hw offloading):

https://forum.banana-pi.org/t/wed-and-beamforming-on-bpi-r3/15099/16

> You need to edit /etc/modules.conf to enable WED. Add a line as follow:
> options mt7915e wed_enable=Y


  zgrep 'WED' /proc/config.gz
  lsmod
  cat /sys/module/mt7915e/parameters/wed_enable
  conntrack -L #should show HW_OFFLOAD when traffic is offloaded
  cat /sys/kernel/debug/ppe*/bind #should show BND (same for entries file)
  
Example configs: https://forum.banana-pi.org/t/hostapd-wifi-speed-not-reach-the-maximum-in-debian11/17642/14
==== USB / PCIe ====

The USB3.0 socket of R3 can only provide a maximum current of 1400mA. [[https://forum.banana-pi.org/t/usb-device-constantly-reconnects-on-bpi-r3/14838/3?u=frank-w|source]]

{{ :en:bpi-r3:bpi-r3-usb-pcie.png?nolink |}}

mPCIe slot is usb-only with SIM connector (bottom of board). PCIe is mapped to m.2 key-m slot for nvme SSD

Sata possible via M.2 KEY-M 2lane interface on bottom side of board (needs PCIe-2-Sata controller!)

I tested mpcie slot with an em7455 [[LTE]] module (+key b adapter)

for m.2-slot there is a patch if nvme is not recognized: https://forum.banana-pi.org/t/bpi-r3-nvme-connection-issue/14563/17
==== GPIO ====

[[gpio]]

==== thermal ====

  cat /sys/class/thermal/thermal_zone0/temp

Thermalpad size: https://forum.banana-pi.org/t/banana-pi-r3-fan-with-pwm/14406/28

Change pwm of fan from 5v to 12v (R317/R318):
[[https://forum.banana-pi.org/t/banana-pi-r3-fan-with-pwm/14406/47|Shematic]]
[[https://forum.banana-pi.org/t/banana-pi-r3-fan-with-pwm/14406/56|location on board]]

Mt76:

  cat /sys/class/ieee80211/phy*/hwmon*/temp1_input

2g4/5g difference: https://github.com/openwrt/mt76/issues/729

FAN-Connector: JST PH 2mm pin-spacing

5V pwm fan: https://de.aliexpress.com/item/1005003663915828.html

trigger pwm-fan:

    echo 1 > /sys/class/thermal/cooling_device0/cur_state
==== leds ====

available via sysfs:

  * green: power
  * blue: status

additional with function

  * wf2g
  * wf5g
  * ssd: blinks on write access on m2-slot (nvme)
  * lte: reported to work by daniel

Wifi-leds are fixed in my 6.1 tree and in mt76 master.

==== case ====

https://forum.banana-pi.org/t/banana-bpi-r3-3d-printed-case/14246/

Case from finas:
https://www.printables.com/model/335936-banana-pi-bpi-r3-modular-case

Higher version added here:


https://www.dropbox.com/s/tng2pi2ud6qd2vo/Banana%20PI%20RPI-3%20case.stl?dl=0
===== Software =====

==== partition layout ====

blocks á 512 byte

^     ^  SD  ^  eMMC  ^
^ bl2 |  34 - 8191  |  in boot0  |
^ u-boot-env |  8192 - 9215  ||
^ factory |  9216 - 13311  ||
^ fip |  13312 - 17407  ||
^ kernel |  17408 - 222207 (100MB)  ||
^ rootfs |  222208 - 12805120 (6144 MB)  ||

bytes (start,size in hex)
^     ^  NAND  ^  NOR  ^
^ bl2 |  0x0, 0x80000  |  0x0, 0x40000  |
^ u-boot-env |  -  |  0x40000, 0x40000  |
^ reserved  |  -  |  0x80000, 0x80000  |
^ factory |  0x80000, 0x300000  |  -  |
^ fip |  0x380000, 0x200000  |  0x100000, 0x80000  |
^ recovery |  -  |  0x180000, 0xa80000  |
^ fit |  -  |  0xc00000, 0x1400000  |
^ ubi |  0x580000, 0x7a80000  |  -  |


=== GPT binaries ===

32MB kernel/256MB root:
{{ :en:bpi-r3:gpt_sd-20220216.bin |}}

create own partition table: (currently i tried to port to python3,but get crc error, so only python2-support):

https://github.com/frank-w/BPI-R3-bsp/tree/r3-atf/tools/mediatek/gpt_editor

  (cd tools/mediatek/gpt_editor/;python mtk_gpt.py --i example/mt7986-sd.json --o GPT_SD)

Created a gpt with 100mb kernel+6GB root partition with an python2 venv


https://github.com/frank-w/u-boot/blob/r3-atf/gpt_sdmmc_100m6g.img

https://github.com/frank-w/u-boot/blob/r3-atf/gpt_emmc_100m6g.img

Gpt img file may cause errors when using parted (main and backup gpt corrupt) or gpt errors in uboot on reboot. This can be also caused by backup-gpt not overridden by image (end of disk).

Parted:

  Error: Both the primary and backup GPT tables are corrupt.  Try making a fresh table, and using Parted's rescue feature to recover partitions.

Uboot (sw reboot):
<code>*** ERROR: Can't read GPT Entries ***
find_valid_gpt: *** ERROR: Invalid GPT ***</code>

This can be fixed with sgdisk by exporting and re-importing the gpt

  sudo sgdisk --backup=bpi-r3_sgdisk.gpt /dev/sdb
  sudo sgdisk --load-backup=bpi-r3_sgdisk.gpt /dev/sdb

=== manual GPT creation ===

{{ :en:bpi-r3:creategpt.sh |script for creating gpt with sgdisk/losetup}} bl2-partition needs legacy-boot flag!

=== Emmc partition creation ===

Todo...currently only via linux initrd from nor/usb

It is possible to create gpt in uboot. Example for rk3568:

https://source.denx.de/u-boot/u-boot/-/blob/master/include/configs/rk3568_common.h#L29

https://elixir.bootlin.com/u-boot/latest/source/include/configs/rockchip-common.h#L85

This creates a env var with the partition definition for rk3568 (not bpi-r3):

<code>
"uuid_disk=${uuid_gpt_disk};" \
"name=loader1,start=32K,size=4000K,uuid=${uuid_gpt_loader1};" \
"name=loader2,start=8MB,size=4MB,uuid=${uuid_gpt_loader2};" \
"name=trust,size=4M,uuid=${uuid_gpt_atf};" \
"name=boot,size=112M,bootable,uuid=${uuid_gpt_boot};" \
"name=rootfs,size=-,uuid="ROOT_UUID
</code>

Which can be used like this:

  mmc dev 0
  gpt write mmc 0 $partitions

defined table this way (blocks only):

<code>
setenv partitions "uuid_disk=${uuid_gpt_disk};name=gpt,start=0,size=34,uuid=${uuid_gpt_table};name=u-boot-env,start=8192,size=1024,uuid=${uuid_gpt_env};name=factory,start=9216,size=4096,uuid=${uuid_gpt_factory};name=fip,start=13312,size=4096,uuid=${uuid_gpt_fip};name=kernel,size=100M,uuid=${uuid_gpt_kernel};name=rootfs,size=0,uuid=${uuid_gpt_rootfs}"
</code>

but i got error on write...maybe because a gpt already exists

<code>
MT7986> printenv partitions
partitions=uuid_disk=;name=gpt,start=0,size=34,uuid=;name=u-boot-env,start=8192,size=1024,uuid=;name=factory,start=9216,size=4096,uuid=;name=fip,start=13312,size=4096,uuid=;name=kernel,size=100M,uuid=;name=rootfs,size=0,uuid=
MT7986> mmc dev 0
switch to partitions #0, OK
mmc0(part 0) is current device
MT7986> gpt write mmc 0 $partitions
Writing GPT: error!
</code>
==== atf / u-boot ====

[[uboot|U-Boot]]

Daniels code:
https://github.com/dangowrt/arm-trusted-firmware/tree/mtksoc-v2.6/

https://git.openwrt.org/?p=openwrt/staging/dangole.git;a=shortlog;h=refs/heads/r3-mt7986
==== linux ====

Own repo: https://github.com/frank-w/BPI-R2-4.14/commits/6.1-main

<code>
./build.sh importconfig
./build.sh #build kernel
</code>
Then copy bpi-r3.itb to card and start from [[uboot#booting_kernel|u-boot]]

=== openwrt ===

configuration: [[openwrt]]

https://git.openwrt.org/openwrt/openwrt.git

Build instructions:
https://forum.banana-pi.org/t/banana-pi-r3-bsp-source-code/14257/2

Or using firmware selector (currently only snapshot): https://firmware-selector.openwrt.org/ (adding luci-ssl)

changing to kernel 6.1: https://forum.banana-pi.org/t/wed-and-beamforming-on-bpi-r3/15099/37

Install: https://forum.banana-pi.org/t/install-openwrt-snapshot-on-bpi-r3/14231/7?u=frank-w

  opkg update
  opkg install luci-ssl

Change network config without luci: https://forum.banana-pi.org/t/banana-pi-r3-cant-save-anything-in-luci/14658/15?u=frank-w

Add more space on storage:
https://forum.banana-pi.org/t/bpi-r3-change-or-add-partion-to-overlay/14240/12
https://forum.banana-pi.org/t/cannot-resize-my-root-partition-on-bpi-r3/13937/5

Modifications from user va1der: https://forum.banana-pi.org/t/bpi-r3-openwrt-whats-the-best-way-to-use-the-rest-of-my-space-on-my-sd-card/15675/10

parted way from user ned14: https://forum.banana-pi.org/t/bpi-r3-openwrt-23-05-0-how-to-extend-production-partition/16572/4

=== debian ===

create image with build.sh createimg from my uboot-repo (atf-r3 branch after building uboot+atf) and add rootfs+kernel

generated GPT from mtk-script has some problems with parted (partprobe reports main gpt is damaged), but it can be mounted with losetup -P

  sudo losetup -P $LDEV $IMGDIR/$IMGNAME.img

writing image to sdcard (image not ready yet):

  gunzip -c bpi-r3_sdmmc_bullseye.img.gz | sudo dd bs=1M status=progress conv=notrunc,fsync of=/dev/sdX

/etc/apt/sources.list:
<code>
deb http://ftp.de.debian.org/debian bullseye main contrib non-free
deb-src http://ftp.de.debian.org/debian bullseye main contrib non-free
deb http://ftp.de.debian.org/debian bullseye-updates main contrib non-free
deb-src http://ftp.de.debian.org/debian bullseye-updates main contrib non-free
deb https://security.debian.org/debian-security bullseye-security main contrib non-free
deb-src http://security.debian.org/debian-security bullseye-security main contrib non-free
</code>

<code>
root@bpi-r3:~# date -s "2022-09-18 18:02:00+0200"
root@bpi-r3:~# ip link set lan4 up
root@bpi-r3:~# ip addr add 192.168.0.19/24 dev lan4       
root@bpi-r3:~# ip route add default via 192.168.0.10     
root@bpi-r3:~# apt update
root@bpi-r3:~# apt install pciutils usbutils traceroute iperf3 net-tools psmisc wget curl
</code>

dnsmasq vs. systemd-resolved:
"Another process is already listening on TCP socket 127.0.0.53:53"

https://unix.stackexchange.com/a/319501


===== issues =====

V1.0:
  * reset switch low/pressed when card in m2 slot ([[https://forum.banana-pi.org/t/bpi-r3-information/12897/42|link]])

V1.1:
  * wifi firmware cannot be started when debug-uart connected ([[https://github.com/openwrt/mt76/issues/702#issuecomment-1264637131|link]])
    * bpi reports only affects profilic adapters, ch340,cp2102,FT4232 are ok ([[https://forum.banana-pi.org/t/bpi-r3-hw-issues/14027/3?u=frank-w|link]])
    * I tested cp2102 (not working),cp2104 (working),ch340G (not working) and ft232rl (working)
    * Possible fix:https://github.com/openwrt/mt76/issues/702#issuecomment-1312284560
  * reset-bug still there
    * is reported to be fixed (removed R171 and R173) in newer v1.1
    * tested in uboot with my v1.1 r3 in uboot and plugged m.2 nvme:
      * <code>MT7986> gpio input 9
gpio: pin 9 (gpio 9) value is 1 //initial value
MT7986> gpio input 9
gpio: pin 9 (gpio 9) value is 0 //pressed</code>
  * dual-nor (no nand) reported by 1 user [[https://forum.banana-pi.org/t/dual-nor-flash-bpi-r3/13962|link]]
  * wifi temperature issue (2g4 seems wrong): https://github.com/openwrt/mt76/issues/729