Inhaltsverzeichnis

Storage

image by garywang

it looks like /dev/mmcblk1, /dev/mmcblk1boot0 and /dev/mmcblk1boot1 are independend devices (bootx not partitions inside /dev/mmcblk1)

preloader

for SD have to be written at 2k-offset (0x800) 

sudo dd if=BPI-R2-EMMC-boot0-DDR1600-20190722-2k.img of=/dev/sdc bs=1k seek=2

(SD-Card needs additional MMC_BOOT & BRLYT header, see below)

for EMMC have to be written at 0-offset (0x0) of boot0-Partition 

sudo dd if=BPI-R2-EMMC-boot0-DDR1600-20190722-0k.img of=/dev/mmcblk1boot0

new preloaderfiles from here: https://github.com/BPI-SINOVOIP/BPI-files/tree/master/SD/100MB

SD-Card

sdcard-bootsektor reverse-engineering http://forum.banana-pi.org/t/boot-fails-with-self-build-u-boot/5460/20

http://forum.banana-pi.org/t/how-to-build-an-ubuntu-debian-sd-image-from-scratch/6805/8

SD-Headers bpi-r2-head440-0k.img bpi-r2-head1-512b.img 

gunzip -c BPI-R2-HEAD440-0k.img.gz | dd of=/dev/loop8 bs=1024 seek=0
gunzip -c BPI-R2-HEAD1-512b.img.gz | dd of=/dev/loop8 bs=512 seek=1

short install-guide

this guide is derived from user ul90 but using a fixed partition table (existing image/sdcard) and variables for loopdevice 

dd if=/dev/zero of=../bpi-r2-buster.img bs=1M count=7168
loopdev=$(losetup -f)
sudo losetup ${loopdev} ../bpi-r2-buster.img
echo $loopdev
sudo dd if=~/Downloads/BPI-R2-preloader-DDR1600-20190722-2k.img of=${loopdev} bs=1k seek=2
sudo dd if=~/Downloads/BPI-R2-HEAD440-0k.img of=${loopdev} bs=1024 seek=0
sudo dd if=~/Downloads/BPI-R2-HEAD1-512b.img  bs=512 seek=1
sudo dd if=/path/to/u-boot/u-boot.bin of=${loopdev} bs=1k seek=320
sudo sfdisk ${loopdev} < ~/Downloads/parttable.dat 
sudo partprobe ${loopdev}
ls ${loopdev}*
sudo mkfs -t vfat ${loopdev}p1
sudo mkfs -t ext4 ${loopdev}p2
sudo fatlabel ${loopdev}p1 BPI-BOOT
sudo e2label ${loopdev}p2 BPI-ROOT

install debian (from bootstrapped rootfs) 

sudo mount ${loopdev}p2 /mnt/
sudo cp -r debian_buster_armhf/. /mnt/
#install kernel-modules to same partition
kernelpack=/path/to/bpi-r2_<version>_main.tar.gz
sudo tar -xzf ${kernelpack} -C /mnt/ --strip-components=1 BPI-ROOT
#install kernel to boot-partition
sudo umount /mnt
sudo mount ${loopdev}p1 /mnt/
sudo tar -xzf ${kernelpack} -C /mnt/ --strip-components=1 BPI-BOOT
#maybe create a uEnv.txt
sudo umount /mnt
sudo losetup -d ${loopdev}
#now write the image to card (make sure /dev/sdc is your sdcard-device and no partition is mounted)
sudo dd if=../bpi-r2-buster.img of=/dev/sdc
sync

Step-by-Step-Guide from "ul90"

1. download binary files:

SD-Headers (old not supporting full uboot-size)

2. Create image file (8GB):

dd if=/dev/zero bs=1M count=7296 | pv | dd of=bpir2.img

3. Load image as virtual drive:

losetup /dev/loop8 bpir2.img

4. Make partitions and format:

parted -s /dev/loop8 mklabel msdos
parted -s /dev/loop8 unit MiB mkpart primary fat32 -- 100MiB 356MiB
parted -s /dev/loop8 unit MiB mkpart primary ext2 -- 356MiB 7295MiB
partprobe /dev/loop8
mkfs.vfat /dev/loop8p1 -I -n BPI-BOOT
mkfs.ext4 -O ^has_journal -E stride=2,stripe-width=1024 -b 4096 /dev/loop8p2 -L BPI-ROOT
sync
parted -s /dev/loop8 print

5. extended boot-headers

gunzip -c BPI-R2-HEAD440-0k.img.gz | dd of=/dev/loop8 bs=1024 seek=0
gunzip -c BPI-R2-HEAD1-512b.img.gz | dd of=/dev/loop8 bs=512 seek=1

6. Write preloader and u-boot bootloader:

dd if=preloader_iotg7623Np1_sd_1600M.bin of=/dev/loop8 bs=1024 seek=2
dd if=u-boot.bin of=/dev/loop8 bs=1024 seek=320
sync

7. Copy rootfs + kernel

create bootstraped rootfs

Install Kernel:

Kernel

8. Remove loop device:

losetup -d /dev/loop8

MMC-Utils

with the mmc-utils you can test out of a running system, if the EMMC-partitioning is correct (should be 48 see change_partition-configuration_of_emmc). 

./mmc extcsd read /dev/mmcblk1
....
Boot configuration bytes [PARTITION_CONFIG: 0x48]
....

i have added the mmc-utils also to my Kernel-Repo (with changed Makefile for Cross-Compile)

a forum user give me the tip here that partition config can be wrote with mmc-utils too 

./mmc bootpart enable 1 1 /dev/mmcblk1
[18:02] root@bpi-r2:~# ./mmc extcsd read /dev/mmcblk1 | grep PARTITION_CONFIG
Boot configuration bytes [PARTITION_CONFIG: 0x00]
[18:02] root@bpi-r2:~# ./mmc bootpart enable 1 1 /dev/mmcblk1
[18:03] root@bpi-r2:~# ./mmc extcsd read /dev/mmcblk1 | grep PARTITION_CONFIG
Boot configuration bytes [PARTITION_CONFIG: 0x48]

install OS on EMMC

http://forum.banana-pi.org/t/bpi-r2-new-image-ubuntu-16-04-v1-2-1-bt-and-wifi-ap-mode-are-working-fine-2017-11-27/4291

  1. change_partition-configuration_of_emmc
  2. activate write mode /dev/mmcblk1boot0:
    echo 0 > /sys/block/mmcblk1boot0/force_ro
  3. write preloader from here to the emmc boot-device:
    • gunzip -c BPI-R2-EMMC-boot0-DDR1600-0k-0905.img.gz | sudo dd of=/dev/mmcblk1boot0 bs=1024 seek=0
    • with bpi-tools: 
      bpi-bootsel BPI-R2-EMMC-boot0-DDR1600-0k-0905.img.gz /dev/mmcblk1boot0
  4. copy of OS-image to EMMC (device=/dev/mmcblk1): 
    • gunzip deb_stretch_emmc.img.gz
dd if=deb_stretch_emmc.img of=/dev/mmcblk1 bs=1M
    • unzip -p <XXX.img.zip> | pv | dd of=<device> bs=10M status=noxfer
    • alternate (with bpi-tools): 
      bpi-copy  <XXX.img.zip> <device>
  5. poweroff, remove SD card and boot again

if sd-card-image does not fit emmc: shrinking image

manual copy of OS